Tops-20

The Hardware Reference Manual was described as for "DECsystem-10/DECSYSTEM-20 Processor" (meaning the DEC PDP-10 and the DECSYSTEM-20).

TOPS-20

login
Developer	Digital Equipment Corporation
Written in	Assembly language
OS family	TENEX
Working state	Discontinued
Initial release	1976; 48 years ago (1976)
Latest release	7.1 / June 1988; 35 years ago (1988-06)
Marketing target	Mainframe computers
Available in	English
Platforms	PDP-10
Default user interface	Command-line interface
License	Proprietary
Preceded by	TENEX

TOPS-20 began in 1969 as the TENEX operating system of Bolt, Beranek and Newman (BBN) and shipped as a product by DEC starting in 1976. TOPS-20 is almost entirely unrelated to the similarly named TOPS-10, but it was shipped with the PA1050 TOPS-10 Monitor Calls emulation facility which allowed most, but not all, TOPS-10 executables to run unchanged. As a matter of policy, DEC did not update PA1050 to support later TOPS-10 additions except where required by DEC software.

TOPS-20 competed with TOPS-10, ITS and WAITS—all of which were notable time-sharing systems for the PDP-10 during this timeframe. TOPS-20 is informally known as TWENEX.

TOPS-20 was based upon the TENEX operating system, which had been created by Bolt Beranek and Newman for Digital's PDP-10 computer. After Digital started development of the KI-10 version of the PDP-10, an issue arose: by this point TENEX was the most popular customer-written PDP-10 operating systems, but it would not run on the new, faster KI-10s. To correct this problem, the DEC PDP-10 sales manager purchased the rights to TENEX from BBN and set up a project to port it to the new machine. In the end, very little of the original TENEX code remained, and Digital ultimately named the resulting operating system TOPS-20.

Some of what came with TOPS-20 was merely an emulation of the TOPS-10 Operating System's calls. These were known as UUO's, standing for Unimplemented User Operation, and were needed both for compilers, which were not 20-specific, to run, as well as user-programs written in these languages. The package that was mapped into a user's address space was named PA1050: PA as in PAT as in compatibility; 10 as in DEC or PDP 10; 50 as in a PDP 10 Model 50, 10/50, 1050.

Sometimes PA1050 was referred to as PAT, a name that was a good fit to the fact that PA1050, "was simply unprivileged user-mode code" that "performed the requested action, using JSYS calls where necessary."

The major ways to get at TOPS-20 capabilities, and what made TOPS-20 important, were

• Commands entered via the command processor, EXEC.EXE
• JSYS (Jump to System) calls from MACro-language (.MAC) programs

The "EXEC" accomplished its work primarily using

• internal code, including calls via JSYS
• requesting services from "GALAXY" components (e.g. spoolers)

Command processor

Rather advanced for its day were some TOPS-20-specific features:

• Command completion
• Dynamic help in the form of

• noise-words - typing DIR and then pressing the ESCape key resulted in
DIRectory (of files)
typing I and pressing the Esc key resulted in
Information (about)

One could then type ? to find out what operands were permitted/required. Pressing Ctrl-T displays status information.

Commands

The following list of commands are supported by the TOPS-20 Command Processor.

JSYS features

JSYS stands for Jump to SYStem. Operands were at times memory addresses. "TOPS-20 allows you to use 18-bit or 30-bit addresses. Some monitor calls require one kind, some the other; some calls accept either kind. Some monitor calls use only 18 bits to hold an address. These calls interpret 18-bit addresses as locations in the current section."

Internally, files were first identified, using a GTJFN (Get Job File Number) JSYS, and then that JFN number was used to open (OPENF) and manipulate the file's contents.

PCL (Programmable Command Language) is a programming language that runs under TOPS-20. PCL source programs are, by default, stored with Filetype .PCL, and enable extending the TOPS-20 EXEC via a verb named DECLARE. Newly compiled commands then become functionally part of the EXEC.

PCL language features

PCL includes:

• flow control: DO While/Until, CASE/SELECT, IF-THEN-ELSE, GOTO
• character string operations (length, substring, concatenation)
• access to system information (date/time, file attributes, device characteristics)

Paul Allen maintained several publicly accessible historic computer systems before his death, including an XKL TOAD-2 running TOPS-20.

See also SDF Public Access Unix System.

• Time-sharing system evolution