Royal Australian Mint

The Mint is situated in the Australian federal capital city of Canberra, in Denison St, in the suburb of Deakin. The Mint was opened in 1965 by Prince Philip, Duke of Edinburgh.

Royal Australian Mint
General information
Location	Deakin, Australian Capital Territory
Opened	22 February 1965
Owner	Australian Government
Design and construction
Architect(s)	Richard Ure
Architecture firm	Department of Works
Main contractor	Civil and Civic E. S. Clementson Pty Ltd
Website
https://www.ramint.gov.au/

Before the opening of the Australian Mint, Australian coins were struck at the Sydney Mint, Melbourne Mint and Perth Mint. As such, the Royal Australian Mint was the first mint in Australia to be independent of the British Royal Mint, in the United Kingdom, which was a British government entity. (Of the three older Australian mints, only Perth Mint has remained; it was a subsidiary of the UK Royal Mint until 1970.)

 

Planning for the mint started in 1959 when it was proposed to move the Melbourne branch of the Royal Mint to Canberra, with a large site in the Canberra suburb of Deakin chosen. The Chief Designing Architect in the Commonwealth Department of Works, Richard Ure, was responsible for the International style design of the mint. It was officially opened by The Duke of Edinburgh on 22 February 1965, coinciding with the introduction of the Australian decimal currency on 14 February 1966. The mint project cost £4.5 million, with Prime Minister Harold Holt noting at the official opening: "We believe that, not only have we achieved a gracious and dignified building in a national setting, but we have a mint also which incorporates the best equipment and most modern minting techniques." The main administration building was constructed by Civil and Civic, while the process building was completed by E. S. Clementson Pty Ltd.

The new mint and the Melbourne Mint operated concurrently while sufficient stockpiles of new coinage were prepared and until it was felt that production in Canberra was proceeding smoothly, after which in 1967 the Melbourne mint was closed. Some staff from the Melbourne mint relocated to Canberra to operate the new mint. However, it was not until the early 1980s that the RAM was able to sustain solitary production of the full set of circulating Australian coins, and so on several occasions in the 1960s and 1970s the RAM contracted production runs to the Perth Mint, the Royal Mint in both London and Llantrisant, and even on one occasion the Royal Canadian Mint.

The mint consists of two buildings, an administration building, and a process building. The administration building houses the engravers, a laboratory, and a vibration-free basement where coinage is measured to ensure correct size and weight.

The mint is an Australian Public Service agency, staffed through the Department of the Treasury.

During 1984-1986, renovations were carried out to support the increasing demand for the production of collector coins, and also to improve the visitor facilities. Visitors can mint their own legal tender coin using visitor presses.

 

The mint serves primarily to manufacture Australia's legal tender precious metal coins. Notes are produced by Note Printing Australia in Melbourne. The mint also produces medals for military and civilian honours, most notably the Order of Australia. The mint produced medals for the 2000 Summer Olympics in conjunction with the Perth Mint. The Royal Australian Mint also produces tokens made for commercial organisations such as casinos, car washes etc.

Since its opening, the mint has produced over fifteen billion coins and has the capacity to produce two million coins per day. Coins have also been struck for several Asian and South Pacific nations, including New Zealand (in 1969), Papua New Guinea, Tonga, Western Samoa, the Cook Islands, Fiji, Malaysia, Thailand, Nepal, Estonia, Bangladesh, Israel, and the Philippines.^{[citation needed]}

 

In November 2001, the mint issued the world's first coin with a double hologram, to commemorate the centenary of Australian federation. The mint also creates bi-metallic coins, and colour printed coins.

On 11 December 2005, the Joint Standing Committee on Public Works tabled a report recommending the refurbishment of the Royal Australian Mint with a projected cost of A$41.2 million. Work was planned to commence in October 2006 with completion dates of June 2008 for the process building, and April 2009 for the administration building.

The refurbishment also planned to introduce industrial robots to the manufacturing process. The work was completed in 2009, and the mint is now open to the public.

In 2014, the Abbott government announced a scoping study into selling the Royal Australian Mint.

• List of mints